Monday, 10 November 2014

LTE Frame Structure

The frame structures for LTE differ between the Time Division Duplex, TDD and the Frequency Division Duplex, FDD modes as there are different requirements on segregating the transmitted data.
There are two types of LTE frame structure:
  1. Type 1:   used for the LTE FDD mode systems.
  2. Type 2:   used for the LTE TDD systems.
Type 1 LTE Frame Structure
The basic type 1 LTE frame has an overall length of 10 ms. This is then divided into a total of 20 individual slots. LTE Subframes then consist of two slots - in other words there are ten LTE subframes within a frame.

Type 1 LTE Frame Structure

The duration of one LTE radio frame is 10 ms. One frame is divided into 10 subframes of 1 ms each, and each subframe is divided into two slots of 0.5 ms each. Each slot contains either six or seven OFDM symbols, depending on the Cyclic Prefix (CP) length. The useful symbol time is 1/15 kHz= 66.6 mircosec. Since normal CP is about 4.69 microsec long, seven OFDM symbols can be placed in the 0.5-ms slot as each symbol occupies (66.6 + 4.69) = 71.29 microseconds. When extended CP (=16.67 microsec) is used the total OFDM symbol time is (66.6 + 16.67) = 83.27 microseconds. Six OFDM symbols can then be placed in the 0.5-ms slot. Frames are useful to send system information. Subframes facilitate resource allocation and slots are useful for synchronization. Frequency hopping is possible at the subframe and slot levels.
Type 2 LTE Frame Structure

Type 2 LTE Frame Structure
(shown for 5ms switch point periodicity).
The subframes may be divided into standard subframes of special subframes. The special subframes consist of three fields;
  • DwPTS - Downlink Pilot Time Slot
  • GP - Guard Period
  • UpPTS - Uplink Pilot Time Stot.
These three fields are also used within TD-SCDMA and they have been carried over into LTE TDD (TD-LTE) and thereby help the upgrade path. The fields are individually configurable in terms of length, although the total length of all three together must be 1ms.
Frame structure Type 2 is applicable to TDD is as shown in the figure. Each radio frame of 10 ms in length consists of two half-frames of 5 ms in length. Each half-frame consists of eight slots of the length Ts=5 ms and three special fields DwPTS, GP, and UpPTS of 1 ms in length.
Different configurations, numbered zero to six, are defined in the standard for the subframe number allocated for the uplink and downlink transmission. Subframe 1 in all configurations and subframe 6 in configurations 0, 1, 2 and 6 consist of DwPTS, GP and UpPTS. All other subframes are defined as two slots.
Switch-point periodicities of 5 ms and 10 ms are supported. The standard defines the table for the uplink and downlink allocations for switch-point periodicity. In the case of a 5-ms switch-point periodicity, UpPTS and subframes 2 and 7 are reserved for uplink transmission.
In the case of a 10-ms switch-point periodicity, UpPTS and subframe 2 are reserved for uplink transmission and subframes 7 to 9 are reserved for downlink transmission.
Subframe 0 and 5 are always for the DL. The subframe following the special SF is always for the UL. The DwPTS field carries synchronization and user data as well as the downlink control channel for transmitting scheduling and control information. The UpPTS field is used for transmitting the PRACH and the Sounding Reference Signal (SRS).
LTE TDD / TD-LTE subframe allocations
One of the advantages of using LTE TDD is that it is possible to dynamically change the up and downlink balance and characteristics to meet the load conditions. In order that this can be achieved in an ordered fashion, a number of standard configurations have been set within the LTE standards.
A total of seven up / downlink configurations have been set, and these use either 5 ms or 10 ms switch periodicities. In the case of the 5ms switch point periodicity, a special subframe exists in both half frames. In the case of the 10 ms periodicity, the special subframe exists in the first half frame only. It can be seen from the table below that the subframes 0 and 5 as well as DwPTS are always reserved for the downlink. It can also be seen that UpPTS and the subframe immediately following the special subframe are always reserved for the uplink transmission.
UPLINK-DOWNLINK CONFIGURATION
DOWNLINK TO UPLINK SWITCH PERIODICITY
SUBFRAME NUMBER


0
1
2
3
4
5
6
7
8
9
0
5 ms
D
S
U
U
U
D
S
U
U
U
1
5 ms
D
S
U
U
D
D
S
U
U
D
2
5 ms
D
S
U
D
D
D
S
U
D
D
3
10 ms
D
S
U
U
U
D
D
D
D
D
4
10 ms
D
S
U
U
D
D
D
D
D
D
5
10 ms
D
S
U
D
D
D
D
D
D
D
6
5 ms
D
S
U
U
U
D
S
U
U
D
Where:
    D is a subframe for downlink transmission
    S is a "special" subframe used for a guard time
    U is a subframe for uplink transmission
Uplink / Downlink subframe configurations for LTE TDD (TD-LTE)


Tuesday, 4 November 2014

QoS (Quality of Service) in LTE

QCI
Resource
Type
Priority
Packet Delay
Budget
Packet Error
Loss Rate
Example Services
1
GBR
2
100ms
10-2
Conversational Voice
2
4
150ms
10-3
Conversational Video(Live Streaming)
3
3
50ms
10-3
Real Time Gaming
4
5
300ms
10-6
Non-Conversational Video (Buffered Streaming)
5
Non-GBR
1
100ms
10-6
IMS Signalling
6
6
300ms
10-6
Video(Bufered streaming) TCP-based (eg. www, e-mail, chat, ftp, p2p file sharing, progressive video,etc)
7
7
100ms
10-3
Voice, Video(Live Streaming) Interactive Gaming
8
8
300ms
10-6
Video(Bufered streaming) TCP-based (eg. www, e-mail, chat, ftp, p2p file sharing, progressive video,etc)
9
9